145 lines
3.4 KiB
Text
145 lines
3.4 KiB
Text
# /etc/modprobe.d/8821cu.conf
|
|
#
|
|
# Purpose: Allow easy access to specific driver options.
|
|
#
|
|
# Edit the following line to change, add or delete options:
|
|
#options 8821cu rtw_drv_log_level=0 rtw_led_ctrl=1 rtw_vht_enable=1 rtw_power_mgnt=1 rtw_beamform_cap=0 rtw_dfs_region_domain=0
|
|
#
|
|
# After editing is complete, save this file (if using nano: Ctrl + x, y, Enter)
|
|
# and reboot to activate the changes.
|
|
#
|
|
# Documentation:
|
|
#
|
|
# -----
|
|
#
|
|
# Log options ( rtw_drv_log_level )
|
|
#
|
|
# 0 = NONE (default)
|
|
# 1 = ALWAYS
|
|
# 2 = ERROR
|
|
# 3 = WARNING
|
|
# 4 = INFO
|
|
# 5 = DEBUG
|
|
# 6 = MAX
|
|
#
|
|
# Note: You can save a log file that only includes RTW log entries by running
|
|
# the following in a terminal:
|
|
#
|
|
# sudo ./save-log.sh
|
|
#
|
|
# Note: The name of the log file will be ```rtw.log```.
|
|
#
|
|
# -----
|
|
#
|
|
# LED options ( rtw_led_ctrl )
|
|
#
|
|
# 0 = Always off
|
|
# 1 = Normal blink (default)
|
|
# 2 = Always on
|
|
#
|
|
# -----
|
|
#
|
|
# VHT options ( rtw_vht_enable )
|
|
#
|
|
# 0 = Disable
|
|
# 1 = Enable (default)
|
|
# 2 = Force auto enable (use only for 5 GHz AP mode)
|
|
#
|
|
# Notes:
|
|
# - A non-default setting can degrade performance greatly in managed mode.
|
|
# - Option 2 allows 80 MHz channel width for 5GHz AP mode, such as when
|
|
# you are using hostapd.
|
|
#
|
|
# -----
|
|
#
|
|
# Power options ( rtw_power_mgnt )
|
|
#
|
|
# 0 = Disable power saving
|
|
# 1 = Power saving on, minPS (default)
|
|
# 2 = Power saving on, maxPS (not recommended for AP mode)
|
|
#
|
|
# -----
|
|
#
|
|
# Beamforming options ( rtw_beamform_cap )
|
|
#
|
|
# 0 = Disable (default)
|
|
# 1 = SU Beamformer
|
|
# 2 = SU Beamformee
|
|
# 10= SU Beamformee and MU Beamformee
|
|
#
|
|
# Note: MU Beamformer is not supported.
|
|
#
|
|
# -----
|
|
#
|
|
# Country Code options ( rtw_country_code )
|
|
#
|
|
# Note: Allows the Country Code to be set in cases where it is unable to
|
|
# be obtained from the operating system.
|
|
#
|
|
# Example for the US: rtw_country_code=US
|
|
# Example for Panama: rtw_country_code=PA
|
|
# Example for Norway: rtw_country_code=NO
|
|
# Example for Kuwait: rtw_country_code=KW
|
|
# Example for Taiwan: rtw_country_code=TW
|
|
#
|
|
# -----
|
|
#
|
|
# DFS Options ( rtw_dfs_region_domain )
|
|
#
|
|
# 0 = NONE (default)
|
|
# 1 = FCC
|
|
# 2 = MKK
|
|
# 3 = ETSI
|
|
#
|
|
# Notes:
|
|
# - Activates DFS channels in AP mode.
|
|
# - DFS FCC 80 MHz channels for hostapd: 52(58), 100(106), 116(122) and 132(138)
|
|
# - For more information: https://en.wikipedia.org/wiki/List_of_WLAN_channels
|
|
#
|
|
# Note: An AP needs to listen on a DFS channel for a period of 60 seconds
|
|
# before transmitting on the channel. If any radar pulses are detected,
|
|
# the AP cannot use that channel and will have to try a different channel.
|
|
#
|
|
# -----
|
|
#
|
|
# Select P2P interface in concurrent mode ( rtw_sel_p2p_iface )
|
|
#
|
|
# 0 = Sets interface 0 to be p2p interface
|
|
# 1 = Sets interface 1 to be p2p interface (default)
|
|
#
|
|
# -----
|
|
#
|
|
# To see all options that are available:
|
|
#
|
|
# $ ls /sys/module/8821cu/parameters/
|
|
#
|
|
# -----
|
|
#
|
|
# To see the values that are in use:
|
|
#
|
|
# $ grep [[:alnum:]] /sys/module/8821cu/parameters/*
|
|
#
|
|
# -----
|
|
#
|
|
# hostapd setup information for rtl8821cu
|
|
# Note: The best settings can vary but the following may be a good place to start.
|
|
#
|
|
# /etc/modprobe.d/8821cu.conf
|
|
# options 8821cu rtw_drv_log_level=0 rtw_led_ctrl=0 rtw_vht_enable=2 rtw_power_mgnt=1 rtw_beamform_cap=0 rtw_dfs_region_domain=1
|
|
#
|
|
# Note: The best setting for `rtw_dfs_region_domain=` will depend on your location.
|
|
#
|
|
# /etc/hostapd/hostapd.conf
|
|
#
|
|
# hw ht capab: 0x862
|
|
# ht_capab=[HT40+][HT40-][SHORT-GI-20][SHORT-GI-40][MAX-AMSDU-7935]
|
|
#
|
|
# hw vht capab: 0x03c00022
|
|
# vht_capab=[MAX-MPDU-11454][SHORT-GI-80][HTC-VHT][MAX-A-MPDU-LEN-EXP7]
|
|
#
|
|
# -----
|
|
|
|
|
|
|
|
|
|
|