Run util/openssl-format-source on ssl/
Some comments and hand-formatted tables were fixed up
manually by disabling auto-formatting.
Reviewed-by: Rich Salz <rsalz@openssl.org>
DTLSv1_client_method() is deprecated, but it was the only way to obtain
DTLS1_BAD_VER support. The SSL_OP_CISCO_ANYCONNECT hack doesn't work with
DTLS_client_method(), and it's relatively non-trivial to make it work without
expanding the hack into lots of places.
So deprecate SSL_OP_CISCO_ANYCONNECT with DTLSv1_client_method(), and make
it work with SSL_CTX_set_{min,max}_proto_version(DTLS1_BAD_VER) instead.
Reviewed-by: Rich Salz <rsalz@openssl.org>
Reviewed-by: Matt Caswell <matt@openssl.org>
We now send the highest supported version by the client, even if the session
uses an older version.
This fixes 2 problems:
- When you try to reuse a session but the other side doesn't reuse it and
uses a different protocol version the connection will fail.
- When you're trying to reuse a session with an old version you might be
stuck trying to reuse the old version while both sides support a newer
version
Signed-off-by: Kurt Roeckx <kurt@roeckx.be>
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
GH: #852, MR: #2452
This was done by the following
find . -name '*.[ch]' | /tmp/pl
where /tmp/pl is the following three-line script:
print unless $. == 1 && m@/\* .*\.[ch] \*/@;
close ARGV if eof; # Close file to reset $.
And then some hand-editing of other files.
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
Some users want to disable SSL 3.0/TLS 1.0/TLS 1.1, and enable just
TLS 1.2. In the future they might want to disable TLS 1.2 and
enable just TLS 1.3, ...
This commit makes it possible to disable any or all of the TLS or
DTLS protocols. It also considerably simplifies the SSL/TLS tests,
by auto-generating the min/max version tests based on the set of
supported protocols (425 explicitly written out tests got replaced
by two loops that generate all 425 tests if all protocols are
enabled, fewer otherwise).
Reviewed-by: Richard Levitte <levitte@openssl.org>
The protocol selection code is now consolidated in a few consecutive
short functions in a single file and is table driven. Protocol-specific
constraints that influence negotiation are moved into the flags
field of the method structure. The same protocol version constraints
are now applied in all code paths. It is now much easier to add
new protocol versions without reworking the protocol selection
logic.
In the presence of "holes" in the list of enabled client protocols
we no longer select client protocols below the hole based on a
subset of the constraints and then fail shortly after when it is
found that these don't meet the remaining constraints (suiteb, FIPS,
security level, ...). Ideally, with the new min/max controls users
will be less likely to create "holes" in the first place.
Reviewed-by: Kurt Roeckx <kurt@openssl.org>
Change various state machine functions to use the prefix ossl_statem
instead.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
Pull out the state machine into a separate sub directory. Also moved some
functions which were nothing to do with the state machine but were in state
machine files. Pulled all the SSL_METHOD definitions into one place...most
of those files had very little left in them any more.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
