In the new state machine if using nbio and we get the header of a
handshake message is one record with the body in the next, with an nbio
event in the middle, then the connection was failing. This is because
s->init_num was getting reset. We should only reset it after we have
read the whole message.
RT#4394
Reviewed-by: Andy Polyakov <appro@openssl.org>
ChangeCipherSpec messages have a defined value. They also may not occur
in the middle of a handshake message. The current logic will accept a
ChangeCipherSpec with value 2. It also would accept up to three bytes of
handshake data before the ChangeCipherSpec which it would discard
(because s->init_num gets reset).
Instead, require that s->init_num is 0 when a ChangeCipherSpec comes in.
RT#4391
Reviewed-by: Andy Polyakov <appro@openssl.org>
Reviewed-by: Matt Caswell <matt@openssl.org>
The write BIO for handshake messages is bufferred so that we only write
out to the network when we have a complete flight. There was some
complexity in the buffering logic so that we switched buffering on and
off at various points through out the handshake. The only real reason to
do this was historically it complicated the state machine when you wanted
to flush because you had to traverse through the "flush" state (in order
to cope with NBIO). Where we knew up front that there was only going to
be one message in the flight we switched off buffering to avoid that.
In the new state machine there is no longer a need for a flush state so
it is simpler just to have buffering on for the whole handshake. This
also gives us the added benefit that we can simply call flush after every
flight even if it only has one message in it. This means that BIO authors
can implement their own buffering strategies and not have to be aware of
the state of the SSL object (previously they would have to switch off
their own buffering during the handshake because they could not rely on
a flush being received when they really needed to write data out). This
last point addresses GitHub Issue #322.
Reviewed-by: Andy Polyakov <appro@openssl.org>
Add doc-nit-check to help find future issues.
Make podchecker be almost clean.
Remove trailing whitespace.
Tab expansion
Reviewed-by: Richard Levitte <levitte@openssl.org>
Defintions of macros similar to _XOPEN_SOURCE belong in command line
or in worst case prior first #include directive in source. As for
macros is was allegedly controlling. One can argue that we are
probably better off demanding S_IS* macros but there are systems
that just don't comply, hence this compromise solution...
Reviewed-by: Rich Salz <rsalz@openssl.org>
In the X509 app check that the obtained public key is valid before we
attempt to use it.
Issue reported by Yuan Jochen Kang.
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
Since with SSL_VERIFY_NONE, the connection may continue and the
session may even be cached, we should save some evidence that the
chain was not sufficiently verified and would have been rejected
with SSL_VERIFY_PEER. To that end when a CT callback returs failure
we set the verify result to X509_V_ERR_NO_VALID_SCTS.
Note: We only run the CT callback in the first place if the verify
result is still X509_V_OK prior to start of the callback.
RT #4502
Reviewed-by: Tim Hudson <tjh@openssl.org>
- Adjust mkerr.pl to produce the line length we used for source
reformating.
- Have mkerr.pl keep track of preprocessor directive indentation
Among others, do not spuriously throw away a #endif at the end of
header files.
- Make sure mkerr.pl specifies any header inclusion correctly
Reviewed-by: Rich Salz <rsalz@openssl.org>
Set ctx->error = X509_V_ERR_OUT_OF_MEM when verificaiton cannot
continue due to malloc failure. Also, when X509_verify_cert()
returns <= 0 make sure that the verification status does not remain
X509_V_OK, as a last resort set it it to X509_V_ERR_UNSPECIFIED,
just in case some code path returns an error without setting an
appropriate value of ctx->error.
Reviewed-by: Richard Levitte <levitte@openssl.org>
Discard useless static engine_id
Add a const qualifier
Fix some spelling
Reviewed-by: Richard Levitte <levitte@openssl.org>
Reviewed-by: Matt Caswell <matt@openssl.org>
chacha20_poly1305_init_key() dereferences NULL when called with inkey !=
NULL && iv == NULL. This function is called by EVP_EncryptInit_ex()
family, whose documentation allows setting key and iv in separate calls.
Reviewed-by: Matt Caswell <matt@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
