Reviewed-by: Andy Polyakov <appro@openssl.org>
Reviewed-by: Kurt Roeckx <kurt@openssl.org>
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/1264)
ChangeCipherSpec messages have a defined value. They also may not occur
in the middle of a handshake message. The current logic will accept a
ChangeCipherSpec with value 2. It also would accept up to three bytes of
handshake data before the ChangeCipherSpec which it would discard
(because s->init_num gets reset).
Instead, require that s->init_num is 0 when a ChangeCipherSpec comes in.
RT#4391
Reviewed-by: Andy Polyakov <appro@openssl.org>
Reviewed-by: Matt Caswell <matt@openssl.org>
Set ctx->error = X509_V_ERR_OUT_OF_MEM when verificaiton cannot
continue due to malloc failure. Also, when X509_verify_cert()
returns <= 0 make sure that the verification status does not remain
X509_V_OK, as a last resort set it it to X509_V_ERR_UNSPECIFIED,
just in case some code path returns an error without setting an
appropriate value of ctx->error.
Reviewed-by: Richard Levitte <levitte@openssl.org>
We now send the highest supported version by the client, even if the session
uses an older version.
This fixes 2 problems:
- When you try to reuse a session but the other side doesn't reuse it and
uses a different protocol version the connection will fail.
- When you're trying to reuse a session with an old version you might be
stuck trying to reuse the old version while both sides support a newer
version
Signed-off-by: Kurt Roeckx <kurt@roeckx.be>
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
GH: #852, MR: #2452
Adjust ssl_set_client_hello_version to get both the minimum and maximum and then
make ssl_set_client_hello_version use the maximum version.
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
MR: #1595
This was done by the following
find . -name '*.[ch]' | /tmp/pl
where /tmp/pl is the following three-line script:
print unless $. == 1 && m@/\* .*\.[ch] \*/@;
close ARGV if eof; # Close file to reset $.
And then some hand-editing of other files.
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
Some users want to disable SSL 3.0/TLS 1.0/TLS 1.1, and enable just
TLS 1.2. In the future they might want to disable TLS 1.2 and
enable just TLS 1.3, ...
This commit makes it possible to disable any or all of the TLS or
DTLS protocols. It also considerably simplifies the SSL/TLS tests,
by auto-generating the min/max version tests based on the set of
supported protocols (425 explicitly written out tests got replaced
by two loops that generate all 425 tests if all protocols are
enabled, fewer otherwise).
Reviewed-by: Richard Levitte <levitte@openssl.org>
The protocol selection code is now consolidated in a few consecutive
short functions in a single file and is table driven. Protocol-specific
constraints that influence negotiation are moved into the flags
field of the method structure. The same protocol version constraints
are now applied in all code paths. It is now much easier to add
new protocol versions without reworking the protocol selection
logic.
In the presence of "holes" in the list of enabled client protocols
we no longer select client protocols below the hole based on a
subset of the constraints and then fail shortly after when it is
found that these don't meet the remaining constraints (suiteb, FIPS,
security level, ...). Ideally, with the new min/max controls users
will be less likely to create "holes" in the first place.
Reviewed-by: Kurt Roeckx <kurt@openssl.org>
This patch contains the necessary changes to provide GOST 2012
ciphersuites in TLS. It requires the use of an external GOST 2012 engine.
Reviewed-by: Matt Caswell <matt@openssl.org>
Reviewed-by: Rich Salz <rsalz@openssl.org>
We were setting |s->renegotiate| and |s->new_session| to 0 twice in
tls_finish_handshake. This is redundant so now we just do it once!
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
We finish the handshake when we move into the TLS_ST_OK state. At various
points we were also unnecessarily finishing it when we were reading/writing
the Finished message. It's much simpler just to do it in TLS_ST_OK, so
remove the other calls.
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
|tls_process_finished| was checking that |peer_finish_md_len| was
non-negative. However neither |tls1_final_finish_mac| or
|ssl3_final_finish_mac| can ever return a negative value, so the check is
superfluous.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
Various enums were introduced as part of the state machine rewrite. As a
matter of style it is preferred for these to be typedefs.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
Change various state machine functions to use the prefix ossl_statem
instead.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
Move some function definitions around within the state machine to make sure
they are in the correct files. Also create a statem_locl.h header for stuff
entirely local to the state machine code and move various definitions into
it.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
Pull out the state machine into a separate sub directory. Also moved some
functions which were nothing to do with the state machine but were in state
machine files. Pulled all the SSL_METHOD definitions into one place...most
of those files had very little left in them any more.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
