With the removal of SSLv2, the s3 structure is always allocated, so
there is little point in having it be an allocated pointer. Collapse
the ssl3_state_st structure into ssl_st and fixup any references.
This should be faster than going through an indirection and due to
fewer allocations, but I'm not seeing any significant performance
improvement; it seems to be within the margin of error in timing.
Reviewed-by: Paul Yang <yang.yang@baishancloud.com>
Reviewed-by: Matt Caswell <matt@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/7888)
If we were using a different type of BIO than a socket BIO then
BIO_get_ktls_send() and BIO_get_ktls_recv() could return the wrong
result.
The above occurred even if KTLS was disabled at compile time - so we should
additionally ensure that those macros do nothing if KTLS is disabled.
Finally we make the logic in ssl3_get_record() a little more robust when
KTLS has been disabled.
[extended tests]
Reviewed-by: Paul Dale <paul.dale@oracle.com>
(Merged from https://github.com/openssl/openssl/pull/8793)
This patch adds support for the Linux TLS Rx socket option.
It completes the previous patch for TLS Tx offload.
If the socket option is successful, then the receive data-path of the TCP
socket is implemented by the kernel.
We choose to set this option at the earliest - just after CCS is complete.
Change-Id: I59741e04d89dddca7fb138e88fffcc1259b30132
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Reviewed-by: Matt Caswell <matt@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/7848)
Previously when a ClientHello arrives with a valid cookie using
DTLSv1_listen() we only "peeked" at the message and left it on the
underlying fd. This works fine for single threaded applications but for
multi-threaded apps this does not work since the fd is typically reused for
the server thread, while a new fd is created and connected for the client.
By "peeking" we leave the message on the server fd, and consequently we
think we've received another valid ClientHello and so we create yet another
fd for the client, and so on until we run out of fds.
In this new approach we remove the ClientHello and buffer it in the SSL
object.
Fixes#6934
Reviewed-by: Ben Kaduk <kaduk@mit.edu>
(Merged from https://github.com/openssl/openssl/pull/7375)
At certain points in the handshake we could receive either a plaintext or
an encrypted alert from the client. We should tolerate both where
appropriate.
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/6887)
Previoulsy we just had max_early_data which controlled both the value of
max early_data that we advertise in tickets *and* the amount of early_data
that we are willing to receive from clients. This doesn't work too well in
the case where we want to reduce a previously advertised max_early_data
value. In that case clients with old, stale tickets may attempt to send us
more early data than we are willing to receive. Instead of rejecting the
early data we abort the connection if that happens.
To avoid this we introduce a new "recv_max_early_data" value. The old
max_early_data becomes the value that is advertised in tickets while
recv_max_early_data is the maximum we will tolerate from clients.
Fixes#6647
Reviewed-by: Paul Dale <paul.dale@oracle.com>
(Merged from https://github.com/openssl/openssl/pull/6655)
The TLS code marks records as read when its finished using a record. The DTLS code did
not do that. However SSL_has_pending() relies on it. So we should make DTLS consistent.
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/6159)
Since the public and private DRBG are per thread we don't need one
per ssl object anymore. It could also try to get entropy from a DRBG
that's really from an other thread because the SSL object moved to an
other thread.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Paul Dale <paul.dale@oracle.com>
Reviewed-by: Matthias St. Pierre <Matthias.St.Pierre@ncp-e.com>
(Merged from https://github.com/openssl/openssl/pull/5547)
In the case of a protocol version alert being sent by a peer the record
version number may not be what we are expecting. In DTLS records with an
unexpected version number are silently discarded. This probably isn't
appropriate for alerts, so we tolerate a mismatch in the minor version
number.
This resolves an issue reported on openssl-users where an OpenSSL server
chose DTLS1.0 but the client was DTLS1.2 only and sent a protocol_version
alert with a 1.2 record number. This was silently ignored by the server.
Reviewed-by: Viktor Dukhovni <viktor@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/5018)
The CCS may be sent at different times based on whether or not we
sent an HRR earlier. In order to make that decision this commit
also updates things to make sure we remember whether an HRR was
used or not.
Reviewed-by: Ben Kaduk <kaduk@mit.edu>
(Merged from https://github.com/openssl/openssl/pull/4701)
Since return is inconsistent, I removed unnecessary parentheses and
unified them.
Reviewed-by: Rich Salz <rsalz@openssl.org>
Reviewed-by: Matt Caswell <matt@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/4541)
Previously if a client received an HRR then we would do version negotiation
immediately - because we know we are going to get TLSv1.3. However this
causes a problem when we emit the 2nd ClientHello because we start changing
a whole load of stuff to ommit things that aren't relevant for < TLSv1.3.
The spec requires that the 2nd ClientHello is the same except for changes
required from the HRR. Therefore the simplest thing to do is to defer the
version negotiation until we receive the ServerHello.
Fixes#4292
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Ben Kaduk <kaduk@mit.edu>
(Merged from https://github.com/openssl/openssl/pull/4527)
Give each SSL object it's own DRBG, chained to the parent global
DRBG which is used only as a source of randomness into the per-SSL
DRBG. This is used for all session, ticket, and pre-master secret keys.
It is NOT used for ECDH key generation which use only the global
DRBG. (Doing that without changing the API is tricky, if not impossible.)
Reviewed-by: Paul Dale <paul.dale@oracle.com>
(Merged from https://github.com/openssl/openssl/pull/4050)
Move the definition of ossl_assert() out of e_os.h which is intended for OS
specific things. Instead it is moved into internal/cryptlib.h.
This also changes the definition to remove the (int) cast.
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/4073)
The return code from tls1_mac is supposed to be a boolean 0 for fail, 1 for
success. In one place we returned -1 on error. This would cause code calling
the mac function to erroneously see this as a success (because a non-zero
value is being treated as success in all call sites).
Fortunately, AFAICT, the place that returns -1 can only happen on an
internal error so is not under attacker control. Additionally this code only
appears in master. In 1.1.0 the return codes are treated differently.
Therefore there are no security implications.
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/3495)
We are quite inconsistent about which alerts get sent. Specifically, these
alerts should be used (normally) in the following circumstances:
SSL_AD_DECODE_ERROR = The peer sent a syntactically incorrect message
SSL_AD_ILLEGAL_PARAMETER = The peer sent a message which was syntactically
correct, but a parameter given is invalid for the context
SSL_AD_HANDSHAKE_FAILURE = The peer's messages were syntactically and
semantically correct, but the parameters provided were unacceptable to us
(e.g. because we do not support the requested parameters)
SSL_AD_INTERNAL_ERROR = We messed up (e.g. malloc failure)
The standards themselves aren't always consistent but I think the above
represents the best interpretation.
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/3480)
When using the -trace option with TLSv1.3 all records appear as "application
data". This adds the ability to see the inner content type too.
Reviewed-by: Richard Levitte <levitte@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/3408)
Fix some comments too
[skip ci]
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/3069)
Found using various (old-ish) versions of gcc.
Reviewed-by: Rich Salz <rsalz@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/2940)
The value of SSL3_RT_MAX_ENCRYPTED_LENGTH normally includes the compression
overhead (even if no compression is negotiated for a connection). Except in
a build where no-comp is used the value of SSL3_RT_MAX_ENCRYPTED_LENGTH does
not include the compression overhead.
Reviewed-by: Richard Levitte <levitte@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/2872)
We also skip any early_data that subsequently gets sent. Later commits will
process it if we can.
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/2737)
This removes the fips configure option. This option is broken as the
required FIPS code is not available.
FIPS_mode() and FIPS_mode_set() are retained for compatibility, but
FIPS_mode() always returns 0, and FIPS_mode_set() can only be used to
turn FIPS mode off.
Reviewed-by: Stephen Henson <steve@openssl.org>
Following on from CVE-2017-3733, this removes the OPENSSL_assert() check
that failed and replaces it with a soft assert, and an explicit check of
value with an error return if it fails.
Reviewed-by: Richard Levitte <levitte@openssl.org>
