There are two copy-paste errors in handling CTR mode. When dealing
with a 2 or 3 block tail, the code branches to the CBC decryption exit
path, rather than to the CTR exit path.
This can lead to data corruption: in the Linux kernel we have a copy
of this file, and the bug leads to corruption of the IV, which leads
to data corruption when we call the encryption function again later to
encrypt subsequent blocks.
Originally reported to the Linux kernel by Ondrej Mosnáček <omosnacek@gmail.com>
CLA: trivial
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Paul Dale <paul.dale@oracle.com>
(Merged from https://github.com/openssl/openssl/pull/8510)
(cherry picked from commit f643deac41)
The add/double shortcut in ecp_nistz256-x86_64.pl left one instruction
point that did not unwind, and the "slow" path in AES_cbc_encrypt was
not annotated correctly. For the latter, add
.cfi_{remember,restore}_state support to perlasm.
Next, fill in a bunch of functions that are missing no-op .cfi_startproc
and .cfi_endproc blocks. libunwind cannot unwind those stack frames
otherwise.
Finally, work around a bug in libunwind by not encoding rflags. (rflags
isn't a callee-saved register, so there's not much need to annotate it
anyway.)
These were found as part of ABI testing work in BoringSSL.
Reviewed-by: Richard Levitte <levitte@openssl.org>
GH: #8109
(cherry picked from commit c0e8e5007b)
ARMv8.3 adds pointer authentication extension, which in this case allows
to ensure that, when offloaded to stack, return address is same at return
as at entry to the subroutine. The new instructions are nops on processors
that don't implement the extension, so that the vetification is backward
compatible.
Reviewed-by: Kurt Roeckx <kurt@roeckx.be>
Reviewed-by: Richard Levitte <levitte@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/8205)
(cherry picked from commit 9a18aae5f2)
As it turns out originally published results were skewed by "turbo"
mode. VM apparently remains oblivious to dynamic frequency scaling,
and reports that processor operates at "base" frequency at all times.
While actual frequency gets increased under load.
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/6406)
Current endianness detection is somewhat opportunistic and can fail
in cross-compile scenario. Since we are more likely to cross-compile
for little-endian now, adjust the default accordingly.
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/5613)
Thumb2 addresses are a bit a mess, depending on whether a label is
interpreted as a function pointer value (for use with BX and BLX) or as
a program counter value (for use with PC-relative addressing). Clang's
integrated assembler mis-assembles this code. See
https://crbug.com/124610#c54 for details.
Instead, use the ADR pseudo-instruction which has clear semantics and
should be supported by every assembler that handles the OpenSSL Thumb2
code. (In other files, the ADR vs SUB conditionals are based on
__thumb2__ already. For some reason, this one is based on __APPLE__, I'm
guessing to deal with an older version of clang assembler.)
It's unclear to me which of clang or binutils is "correct" or if this is
even a well-defined notion beyond "whatever binutils does". But I will
note that https://github.com/openssl/openssl/pull/4669 suggests binutils
has also changed behavior around this before.
Reviewed-by: Andy Polyakov <appro@openssl.org>
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/5431)
Signed-off-by: Patrick Steuer <patrick.steuer@de.ibm.com>
Reviewed-by: Andy Polyakov <appro@openssl.org>
Reviewed-by: Tim Hudson <tjh@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/4634)
Signed-off-by: Patrick Steuer <patrick.steuer@de.ibm.com>
Reviewed-by: Andy Polyakov <appro@openssl.org>
Reviewed-by: Tim Hudson <tjh@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/4634)
Around 138 distinct errors found and fixed; thanks!
Reviewed-by: Kurt Roeckx <kurt@roeckx.be>
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/3459)
It's not clear if it's a feature or bug, but binutils-2.29[.1]
interprets 'adr' instruction with Thumb2 code reference differently,
in a way that affects calculation of addresses of constants' tables.
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
(Merged from https://github.com/openssl/openssl/pull/4669)
Extend the s390x capability vector to store the longer facility list
available from z13 onwards. The bits indicating the vector extensions
are set to zero, if the kernel does not enable the vector facility.
Also add capability bits returned by the crypto instructions' query
functions.
Signed-off-by: Patrick Steuer <patrick.steuer@de.ibm.com>
Reviewed-by: Andy Polyakov <appro@openssl.org>
Reviewed-by: Tim Hudson <tjh@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/4542)
An instruction's QUERY function is executed at initialization, iff the required
MSA level is installed. Therefore, it is sufficient to check the bits returned
by the QUERY functions. The MSA level does not have to be checked at every
function call.
crypto/aes/asm/aes-s390x.pl: The AES key schedule must be computed if the
required KM or KMC function codes are not available. Formally, the availability
of a KMC function code does not imply the availability of the corresponding KM
function code.
Signed-off-by: Patrick Steuer <patrick.steuer@de.ibm.com>
Reviewed-by: Andy Polyakov <appro@openssl.org>
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/4501)
Signed-off-by: Patrick Steuer <patrick.steuer@de.ibm.com>
Reviewed-by: Andy Polyakov <appro@openssl.org>
Reviewed-by: Rich Salz <rsalz@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/4501)
Names were not removed.
Some comments were updated.
Replace Andy's address with openssl.org
Reviewed-by: Andy Polyakov <appro@openssl.org>
Reviewed-by: Paul Dale <paul.dale@oracle.com>
(Merged from https://github.com/openssl/openssl/pull/4516)
"Optimize" is in quotes because it's rather a "salvage operation"
for now. Idea is to identify processor capability flags that
drive Knights Landing to suboptimial code paths and mask them.
Two flags were identified, XSAVE and ADCX/ADOX. Former affects
choice of AES-NI code path specific for Silvermont (Knights Landing
is of Silvermont "ancestry"). And 64-bit ADCX/ADOX instructions are
effectively mishandled at decode time. In both cases we are looking
at ~2x improvement.
AVX-512 results cover even Skylake-X :-)
Hardware used for benchmarking courtesy of Atos, experiments run by
Romain Dolbeau <romain.dolbeau@atos.net>. Kudos!
Reviewed-by: Rich Salz <rsalz@openssl.org>
The assembler already knows the actual path to the generated file and,
in other perlasm architectures, is left to manage debug symbols itself.
Notably, in OpenSSL 1.1.x's new build system, which allows a separate
build directory, converting .pl to .s as the scripts currently do result
in the wrong paths.
This also avoids inconsistencies from some of the files using $0 and
some passing in the filename.
Reviewed-by: Richard Levitte <levitte@openssl.org>
Reviewed-by: Andy Polyakov <appro@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/3431)
Fix some comments too
[skip ci]
Reviewed-by: Tim Hudson <tjh@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/3069)
Even though Apple refers to Procedure Call Standard for ARM Architecture
(AAPCS), they apparently adhere to custom version that doesn't follow
stack alignment constraints in the said standard. [Why or why? If it's
vendor lock-in thing, then it would be like worst spot ever.] And since
bsaes-armv7 relied on standard alignment, it became problematic to
execute the code on iOS.
Reviewed-by: Rich Salz <rsalz@openssl.org>
Initial IV was disregarded on SHAEXT-capable processors. Amazingly
enough bulk AES128-SHA* talk-to-yourself tests were passing.
Reviewed-by: Richard Levitte <levitte@openssl.org>
(Merged from https://github.com/openssl/openssl/pull/2992)
This removes the fips configure option. This option is broken as the
required FIPS code is not available.
FIPS_mode() and FIPS_mode_set() are retained for compatibility, but
FIPS_mode() always returns 0, and FIPS_mode_set() can only be used to
turn FIPS mode off.
Reviewed-by: Stephen Henson <steve@openssl.org>
- harmonize handlers with guidelines and themselves;
- fix some bugs in handlers;
- add missing handlers in chacha and ecp_nistz256 modules;
Reviewed-by: Rich Salz <rsalz@openssl.org>
Some of stone-age assembler can't cope with r0 in address. It's actually
sensible thing to do, because r0 is shunted to 0 in address arithmetic
and by refusing r0 assembler effectively makes you understand that.
Reviewed-by: Rich Salz <rsalz@openssl.org>
crypto/evp/e_aes.c: Types of inp and out parameters of
AES_xts_en/decrypt functions need to be changed from char to
unsigned char to avoid build error due to
'-Werror=incompatible-pointer-types'.
crypto/aes/asm/aes-s390x.pl: Comments need to reflect the above
change.
Signed-off-by: Patrick Steuer <psteuer@mail.de>
Reviewed-by: Rich Salz <rsalz@openssl.org>
Reviewed-by: Richard Levitte <levitte@openssl.org>
Reviewed-by: Matt Caswell <matt@openssl.org>
CLA: trivial
The prevailing style seems to not have trailing whitespace, but a few
lines do. This is mostly in the perlasm files, but a few C files got
them after the reformat. This is the result of:
find . -name '*.pl' | xargs sed -E -i '' -e 's/( |'$'\t'')*$//'
find . -name '*.c' | xargs sed -E -i '' -e 's/( |'$'\t'')*$//'
find . -name '*.h' | xargs sed -E -i '' -e 's/( |'$'\t'')*$//'
Then bn_prime.h was excluded since this is a generated file.
Note mkerr.pl has some changes in a heredoc for some help output, but
other lines there lack trailing whitespace too.
Reviewed-by: Kurt Roeckx <kurt@openssl.org>
Reviewed-by: Matt Caswell <matt@openssl.org>
MIPS[32|64]R6 is binary and source incompatible with previous MIPS ISA
specifications. Fortunately it's still possible to resolve differences
in source code with standard pre-processor and switching to trap-free
version of addition and subtraction instructions.
Reviewed-by: Richard Levitte <levitte@openssl.org>
This is useful in Linux kernel context, in cases data happens
to be fragmented and processing can take multiple calls.
Reviewed-by: Rich Salz <rsalz@openssl.org>
